Replacement Item Instruments
Showing 16–30 of 79 results
-
Burnishing tools facilitate accurate and easy use of Testex Press-O-Film replica tape. Multiple types available, as follows:
- Stick-type. Economical plastic, sold in packs of 10, these have 8mm round ends. Use with all types of Testex tape.
- Burnishing ball. Designed to use with optical grade tape, for use with the RTR 3D probe.
- High Accuracy tool. Updated with a spring-loaded ball for the most consistent results. Use with standard Testex tape.
-
INDRTRCLEANRecommended best practice when performing replica tape tests with PosiTector RTR instruments is to thoroughly clean the anvils (test surfaces) before performing the test. These Cleaning Cards are premoistened with alcohol and are excellent for removing bits of adhesive and debris from the anvils. Each new RTR comes complete with 5 cleaning cards and additional quantities are available here as needed, in packs of 20.INDRTRCLEANRecommended best practice when performing replica tape tests with PosiTector RTR instruments is to thoroughly clean the anvils (test surfaces) before performing the test. These Cleaning Cards are premoistened with alcohol and are excellent for removing bits of adhesive and debris from the anvils. Each new RTR comes complete with 5 cleaning cards and additional quantities are available here as needed, in packs of 20.
-
The Bresle method of testing surfaces for salt contamination is recognized by ISO and ASTM standards. The DeFelsko SST test probe is an easy and accurate way to conduct these tests. Test patches are required to perform them and DeFelsko has multiple options, as follows:
- PosiPatch™. This innovative product utilizes a reusable patch, held by a magnetic ring against the surface. Available in 2 configurations:
- Rigid ring. Preferred for flat surfaces or round surfaces with greater than 40 inch diameter.
- Flexible ring. Preferred for round surfaces between 4 and 40 inch OD, or a minimum of 4.5 inches ID.
- Saves time and money vs. disposable patches.
- Utilizes a plastic needle - no sharp hypodermic needles required!
- Latex Disposable. The conventional Latex Adhesive Bresle Method Patch has a sample test volume range of up to 15 ml (the only DeFelsko version with this range) for applications where the spec requires this.
- Latex-Free Disposable. Similar to latex disposables but lower in cost, the DeFelsko Adhesive Bresle Method Patch is suitable when the 15 ml sample size of the latex version is not required.
Note: Both disposable options from DeFelsko feature low-tack adhesive with TearGuard™ technology for easy patch removal. No residue to clean from the surface when using any DeFelsko SST test patch option!
- PosiPatch™. This innovative product utilizes a reusable patch, held by a magnetic ring against the surface. Available in 2 configurations:
-
Reduce the investment required to convert to PosiTest® HHD equipment by using these adaptors. Makes other brands of brush and spring electrodes compatible with DeFelsko High Voltage Holiday Detectors. (Adaptor not required for SPY electrodes)
- Three adaptors available with MPN's shown, as follows:
- HHDPCWIADPT - PCWI Adaptor
- HHDTRADPT - Tinker & Rasor Adaptor
- HHD266ADPT - 266 and 280 Adaptor
- Three adaptors available with MPN's shown, as follows:
-
BlastOne offers all instruments and accessories from the DeFelsko range on-line, for easy ordering, access to operational manuals, and more. Inspection instruments are an investment worth protecting and DeFelsko has a range of protective cases available, as follows:
- The PosiTector Case. Sturdy hardshell design designed to carry a PosiTector gage / body and multiple probes. Space for manuals, calibration certificates, and more. MPN: CASEINSP
- The Pelican Standard Inspection Kit Case. Lightweight, watertight, and crushproof, this case securely stores a PosiTector Gage and 3+ PosiTector probes with customized foam inserts. 30 x 22.5 x 13.2cm. The MPN is CASEINSP-P.
- The Pelican Large Inspection Kit Case. Like the smaller Standard version above, this unit is lightweight, watertight, and crushproof but is larger to accommodate 5+ probes as well as SST Soluble Salt Tester accessories. 43.2 x 29.7 x 15.7cm. The MPN is CASEINSPL-P.
- The Pelican Adhesion Tester Case. Heavy duty, waterproof construction features customized foam inserts for the PosiTest AT-A automatic tester. 46.2 x 34 x 17cm. The MPN is CASEATAB-P.
-
INDPOUCHDFTBlastOne carries all DeFelsko instruments, accessories, and supplies. This leather pouch has been specially designed for the PosiTest DFT gauge and economically provides protection for your investment. MPN: POUCH-DFTINDPOUCHDFTBlastOne carries all DeFelsko instruments, accessories, and supplies. This leather pouch has been specially designed for the PosiTest DFT gauge and economically provides protection for your investment. MPN: POUCH-DFT
-
Thickness Standards are used to verify the accuracy and operation of coating thickness gauges. As a component of ISO 9000 or in-house quality control procedures, they are a practical alternative to sending instruments to DeFelsko for calibration. These Plastic Shims (aka foils) are low-cost alternative to coated metal plates. They are available in Certified (individual shims or full sets) and in Un-Certified sets. Accuracy is somewhat less than metal plates and they are more sensitive to heat. They are intended for use over a Zero Plate, or over an uncoated substrate. A set of un-certified plastic shims is included with most electronic DeFelsko coating thickness gauges. Replacement sets and certified options are available here as follows:
- Un-Certified. These are checked for accuracy within tolerance shown below at DeFelsko, but are not traceable to any standard. They come as a set of 5 only, in the following approximate thicknesses:
- 25 microns / 1 mil (Orange), +- 20% accuracy
- 50 microns / 2 mils (Red), +- 10% accuracy
- 125 microns / 5 mils (Blue), +- 5% accuracy
- 250 microns / 10 mils (Brown), +- 5% accuracy
- 500 microns / 20 mils (Yellow), +- 5% accuracy
- Certified. Includes certificate of calibration traceable to PTB and all are accurate to within 2 microns / 0.08 mils. Available in the following thicknesses individually, or as a complete set of 8 shims:
- 25 microns / 1 mil (Orange)
- 50 microns / 2 mils (Red)
- 75 microns / 3 mils (Green)
- 125 microns / 5 mils (Blue)
- 250 microns / 10 mils (Brown)
- 500 microns / 20 mils (Yellow)
- 1000 microns / 40 mils (White)
- 1500 microns / 60 mils (Black)
- Un-Certified. These are checked for accuracy within tolerance shown below at DeFelsko, but are not traceable to any standard. They come as a set of 5 only, in the following approximate thicknesses:
-
INDUSBAC
The DeFelsko® AC Power Kit is the ultimate solution for uninterrupted use of your battery-operated PosiTector® devices. This versatile kit enables continuous operation without reliance on batteries, featuring a USB cable for direct connection to a PC and an AC power adapter for wall outlets. Compatible with PosiTector® 6000, 200, SPG, RTR H, RTR 3D, DPM, IRT, SST, UTG, SHD, BHI, and GLS models with serial numbers greater than 864000, it includes a selection of electrical plugs to accommodate various international outlets, ensuring your PosiTector® is always ready for action, whether in the lab, on the production floor, or in the field.
- Designed for uninterrupted use of PosiTector® devices
- Includes USB cable and AC power adapter for versatile power options
- Compatible with a wide range of PosiTector® models
- Selection of electrical plugs for international compatibility
- Ideal for continuous operation without battery dependency
INDUSBACThe DeFelsko® AC Power Kit is the ultimate solution for uninterrupted use of your battery-operated PosiTector® devices. This versatile kit enables continuous operation without reliance on batteries, featuring a USB cable for direct connection to a PC and an AC power adapter for wall outlets. Compatible with PosiTector® 6000, 200, SPG, RTR H, RTR 3D, DPM, IRT, SST, UTG, SHD, BHI, and GLS models with serial numbers greater than 864000, it includes a selection of electrical plugs to accommodate various international outlets, ensuring your PosiTector® is always ready for action, whether in the lab, on the production floor, or in the field.
- Designed for uninterrupted use of PosiTector® devices
- Includes USB cable and AC power adapter for versatile power options
- Compatible with a wide range of PosiTector® models
- Selection of electrical plugs for international compatibility
- Ideal for continuous operation without battery dependency